Skip to content
Yaptake
FeaturesPricingCompareDocs
Download free
Yaptake/Free tools/LUFS meter

Measure LUFS and true peak, free in your browser

Checked November 17, 2026 against ITU-R BS.1770-4, the tool’s source and Yaptake’s

Open a recording to measure its integrated loudness in LUFS and its true peak in dBTP, as ITU-R BS.1770-4 defines them. The meter then gives the gain that takes it to −14, −16 or −23 LUFS and saves a WAV at that level. It runs in your browser, so nothing is uploaded, and it measures the way Yaptake does before it exports a video.

Measure the loudness

Your recording stays on this device. Open a WAV, MP3 or M4A file, or a video whose sound this browser plays, up to 30 minutes long.

What the numbers mean

  • Integrated loudness is the loudness of the whole recording, in LUFS: loudness units relative to full scale. Frequencies are weighted roughly as hearing weights them, and silence and quiet passages don’t pull it down, because blocks below −70 LUFS, and blocks more than 10 LU below the rest, are left out. One LU is one decibel.
  • True peak is the highest level the sound reaches, in dBTP, including between samples, where playback can clip even when no sample is at full scale. The meter finds it by resampling the sound at four times its rate.

Stereo counts both channels and mono counts one, so a mono file reads about 3 LU below the same sound in stereo. A recording with more channels is measured as a mono mix.

Which target to use

TargetWhere it’s used
−14 LUFSA common choice for short videos and music streaming. Yaptake’s export aims for it, with true peaks under −1 dBTP.
−16 LUFSA common target for podcasts and spoken word.
−23 LUFSEBU R 128, the European broadcast standard, with true peaks under −1 dBTP.

Saving at a target

Each target’s button saves the recording with that gain as a 16-bit WAV at 48 kHz. It is a plain change of level, with no limiter or compressor, so the gain stops short of a target when reaching it would push the true peak above −1.5 dBTP, or would take more than 20 dB, which would raise the room’s noise as much. The meter says where it stops and why.

Yaptake does more when it exports: it levels the sound to −14 LUFS and holds the peaks down with a limiter, for up to 6 dB more than a plain gain could give.

Questions

What is LUFS?

LUFS, loudness units relative to full scale, measure how loud a recording sounds rather than how high its peaks go. A difference of 1 LU is a difference of 1 dB.

What LUFS should a video for Reels, TikTok or Shorts be?

−14 LUFS with true peaks under −1 dBTP is a common choice for short videos, and what Yaptake’s export aims for.

How accurate is the meter?

It meets the EBU’s test cases for loudness meters, EBU Tech 3341, within 0.1 LU for integrated loudness, and its true-peak cases within their limits. The same cases test the meter in Yaptake.

Can it measure the sound of a video?

Yes, when your browser can decode the video’s sound, as it can for most MP4 and MOV files.

Is my recording uploaded?

No. The meter runs in your browser, on the file you open, and nothing is sent anywhere.

Try Yaptake

Yaptake is a video editor for Mac that edits a talking video by its transcript, and levels its sound to −14 LUFS as it exports. Everything runs on your Mac.

Your first 3 successful exports on each Mac are free, with no watermark, account or credit card required. After that, exporting is $9.99 a month or $79 a year. Editing is always free.

Download for MacSilence removerThe offline editorAll free tools

DocumentationCompareFree toolsPrivacyTermsSupport
Your Privacy Choices Hraness